Urządzenia sterujące — CR25-100 — CR25 CR Seria CR Mosiężny zawór bezpieczeństwa, regulowany zakres ciśnienia 0-100 psi, 1/4 męski NPT

Name: Urządzenia sterujące — CR25-100 — CR25 CR Seria CR Mosiężny zawór bezpieczeństwa, regulowany zakres ciśnienia 0-100 psi, 1/4 męski NPT
Brand: Control Devices
SKU: 0372657518635
Price: 190.15 PLN
Availability: InStock

Brand:Control Devices

3.6/5

zł
190.15

Ten ciśnieniowy zawór nadmiarowy CR25-100 firmy Control Devices ma mosiężny korpus, regulowane ciśnienie nadmiarowe, przyłącze wlotowe z gwintem zewnętrznym 1/4 NPT i pierścień uszczelniający typu O-ring z fluorowęglowodoru. Mosiężny korpus zaworu, mosiężne gniazdo zaworu i grzybek ze stali nierdzewnej są odporne na korozję i mogą być używane w temperaturach roboczych do 250 stopni F. Zawór można regulować w zakresie otwarcia od 0 do 100 psi za pomocą nylonowego pokrętła w stylu mikrometru. Ten zawór bezpieczeństwa ma standardowe natężenie przepływu 6 stóp sześciennych na minutę (SCFM) i nadaje się do zastosowań związanych z redukcją ciśnienia przy niskim przepływie, takich jak bezzbiornikowe sprężarki powietrza. Zawory nadmiarowe usuwają nadciśnienie lub podciśnienie z systemu. Otwory zaworów umożliwiają ucieczkę płynów lub gazów w celu zmniejszenia ciśnienia, a następnie zamykają się, gdy zawór osiągnie granicę ciśnienia ponownego osadzania. Zmniejszają również nadmiar próżni, otwierając się w celu uwolnienia gazu do układu, a następnie zamykając się po osiągnięciu granicy niskiego ciśnienia. Niektóre zawory nadmiarowe mają mechanizm regulacji do ustawiania ciśnienia, przy którym zawór się otwiera, dzięki czemu nadają się do różnych zastosowań. Zawory nadmiarowe są oceniane zgodnie z objętością cieczy lub gazu, która może przez nie przepływać, a materiał, z którego zbudowany jest zawór, musi być odpowiedni dla płynu lub gazu, który może być korozyjny lub w ekstremalnej temperaturze, w której działa. Zawory nadmiarowe są używane w różnych zastosowaniach, takich jak sprężarki powietrza, produkcja petrochemiczna i chemiczna, przetwarzanie gazu ziemnego i wytwarzanie energii. Control Devices produkuje zawory i inne urządzenia sterujące przepływem. Firma założona w 1963 roku ma swoją siedzibę w Fenton, MO.

Kwota

Dodaj do koszyka Kup Teraz

EAN: 0372657518635

Kategorie Przemysłowe i naukowe, Hydraulika, pneumatyka i hydraulika, Armatura, Zawory, Zawory bezpieczeństwa,

Nylonowe pokrętło w stylu mikrometru do regulacji odciążenia ciśnienia. Silikonowy o-ring zapewnia szczelność do 10 procent ustawionego ciśnienia. Mosiężna konstrukcja i sprężyna ze stali nierdzewnej zapewniają odporność na korozję. Złącze wlotowe z gwintem zewnętrznym 1/4 NPT. Ciśnienie upustowe regulowane w zakresie od 0 do 100 psi.

Brand	Control Devices
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Stainless Steel
Inlet Connection Size	0.25 Inches
Inlet Connection Type	National Pipe Tapered
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item model number	CR25-100
Manufacturer	Control Devices
Material	Brass
Outlet Connection Type	MNPT
Package Dimensions	4.33 x 3.23 x 1.69 inches; 2.4 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem^*

Twoja ocena

Scritto da: Mac

1 year of use and still good

I bought this to install on my steam sterilizer. The sterilizer reaches 121°C (250°F) and 15-18psi. I obviously have an additional safety release valve and a pressure gauge. The markings on the adjustable valve seem to be within the stated tolerance. It does occasionally get stuck closed. I learned it is best if I open it completely to vent before building pressure and then adjust it when the desired pressure is reached to allow very minimal venting. It never gets stuck if this is done. It always closes and does hold a vacuum upon cooling. All in all it does exactly what I want. I may replace it soon with the same valve simply because it is cheap and for peace of mind. 4/5 for overall quality 5/5 for quality at low price

Scritto da: Caitlin G

Good as a PRV

I’m using this PRV as part of a pressure fermentation and spunding rig. For my use it works really well with one exception. It needs to be used with a pressure gauge since the gauge on the pressure adjustment is 10-15 psi off. 10 psi on the PRV is actually 15 psi on a gauge.

Scritto da: Janice Villanueva

it works pretty cool so far for what I use it for

It relieves a fair amount of pressure. I believe more expensive valves relieve more pressure if that is what you need. Overall, it works pretty cool so far for what I use it for. Ignore the numbers used for measuring on this item. It's only there to make the item more attractive to buy. I had to buy a nut for mine in order to install it, which wasn't very hard. I use mine along with a pressure gauge on a homemade low pressure 55 gal steel sterilizing/pasteurizing drum. I never allow the tank to exceed 2 psi. I use this item basically to begin relieving pressure when the pressure reaches 1-1.5 psi. I adjust it according to my pressure gauge. It is most useful to me really in that it is an alarm for me to turn the propane down or open more wide the main relief valve. And I'm sure it helps prevent the psi from exceeding the point that it is set at. I do believe that if I turned the propane all the way up that this pressure relief valve would not be able to prevent my tank from exceeding the 2 psi that I am able to set it at. This is not a proven fact because I have not tested it. I'm just judging by the amount of pressure that this valve actually relieves. It relieves enough pressure that I don't try to find a better relief valve. But if I wanted to be perfectly safe i would wish for a valve that relieves more pressure so that to be sure that it would be impossible to exceed the 2 psi mark that I can set it at using this valve.

Scritto da: Book Lover

Seems to work great! I had it set at 75, and it didn't leak at 50PSI.

Seems to work great! I had it set at 75, and it didn't leak at 50PSI. The spring loaded design looks like this design should be fairly robust and fool proof. I heard that it leaked for some people, but my application didn't. I used thread tape and never opened it all the way up, so it seems to work for me.

Scritto da: D. Morrison

Leaking Valve FIXED

Like others, my PRV developed a leak out of nowhere (it would never fully close). I removed it from the fitting and found that a small piece of thread tape had become trapped in the valve seat, causing the leak. After removing this and reassembling, the leak is gone and the valve operates properly. I would be cautious using this in a setup where any debris could enter the valve. The markings are wildly wrong, but with a gauge in the system this is easily set to low pressure (10 PSI). I do not know if it would work toward the higher end of the rated range.

Scritto da: V. Williams

Tested positive for lead content

This device seems well made and durable, but if you are intending to attach it to a beverage line or passing liquid near it that is intended for consumption, think twice. Having read about various factories mixing lead in their brass, I decided to buy a reliable lead testing kit and tested all my recent brass connector purchases. Four out of 16 items tested positive for lead content. This item was one with lead in it. Photo provided with a sample of many items I tested.

Scritto da: David Swift

Excellent piece of hardware

Bought for a safety valve on a science project. Nice fine adjustment. Doesn't leak until set point is hit. Closes tight when pressure goes below set point. Tested with some pretty fast transients and it worked great. Could have done without the factory installed thread sealant.

Scritto da: Alex

Does the Job

I use it as an emergency air pressure release to bleed off back pressure from my Medo LA45C pump for my guppies LOL. Set it to open at 1.5 PSI I actually dump excess air through a ball valve and huge 1/5" x 8" airstones so my backpressure on the ball valve is set to 0.5PSI . but if airstones plug up this valve opens to keep back pressure from blowing my piston rings on the Medo.