Ogólne narzędzia do obróbki drewna jaskółczy ogon - 12 zestaw szablonów do produkcji mebli i szafek drewnianych

Name: Ogólne narzędzia do obróbki drewna jaskółczy ogon - 12 zestaw szablonów do produkcji mebli i szafek drewnianych
Brand: General Tools
SKU: 0069060366747
Price: 522.58 PLN
Availability: InStock

Brand:General Tools

3.2/5

zł
522.58

Ten 12 ogólnych narzędzi do obróbki drewna na jaskółczy ogon to łatwy sposób na tworzenie profesjonalnych połączeń, w tym połączeń półślepych, od krawędzi do krawędzi, kwadratowych i przelotowych. Zintegrowane zaciski umożliwiają precyzyjne mocowanie przyrządu do przedmiotu obrabianego i nie ma potrzeby przykręcania przyrządu do stołu warsztatowego, jak zalecają inne firmy. Gdy ciągle podnosisz i odkładasz frezarkę z odsłoniętym bitem, wygodnie jest zaparkować narzędzie na bezpiecznej platformie. Pamiętać; połączenie na jaskółczy ogon jest bardzo mocne, ponieważ ogony i szpilki są ukształtowane, co utrudnia ich rozerwanie i jest praktycznie niemożliwe po dodaniu kleju. W General Tools oferujemy ponad 1000 produktów do wyboru. Z dumą zapewniamy handlowcom, rzemieślnikom i majsterkowiczom na całym świecie szeroką gamę przystępnych cenowo mechanicznych narzędzi ręcznych o specjalnym przeznaczeniu oraz precyzyjny sprzęt pomiarowy i inspekcyjny.

Kwota

Dodaj do koszyka Kup Teraz

EAN: 0069060366747

Kategorie Narzędzia i ulepszenia domu, Narzędzia elektryczne i ręczne, Części i akcesoria do elektronarzędzi, Akcesoria do jigów,

NARZĘDZIA OGÓLNE: Jesteśmy uznanym liderem w opracowywaniu specjalistycznych narzędzi precyzyjnych przeznaczonych do zapewniania wyjątkowej obsługi klienta. Zachęcamy rzemieślników i majsterkowiczów do korzystania z naszych maszyn, aby pracować mądrzej, lepiej mierzyć i produktywnie naprawiać. PRZYRZĄDY DO OBRÓBKI DREWNA: Uzupełnij profesjonalne mocowanie stolarskie za pomocą naszej profesjonalnej piły. Możesz łatwo dostosować interfejs mikroprzyrządu, aby tworzyć luźne lub ciasne połączenia, a pokrętła kontrolne obiecują wygodne i dokładne użytkowanie. MARKER DO DREWNA: Profesjonaliści i nowicjusze mogą wykonywać połączenia półślepe lub na jaskółczy ogon, w tym połączenia skrzynkowe. Ma różne zastosowania, takie jak naprawa, dzięki czemu jest poręcznym i niezbędnym narzędziem do posiadania wśród innych akcesoriów ręcznych i zasilających. JOINT BOX: Nasz zestaw zawiera 1 narzędzie do łączenia na jaskółczy ogon i pojedynczy frez na jaskółczy ogon 14 stopni, 1/2 do użytku ze stołem ręcznym lub routerem stołowym. Podręcznik użytkownika zawiera wskazówki dla początkujących i profesjonalistów, ułatwiające korzystanie z części. REGULOWANY PRZYRZĄD DOVETAIL: 1-częściowy aluminiowy układ zapewnia równomierne dopasowanie obu końców połączenia na jaskółczy ogon, a zintegrowana konstrukcja zacisku dopasowuje się do dowolnej szerokości deski. Nasza maszyna jest idealna do projektów wewnątrz i na zewnątrz oraz do napraw domowych.

Batteries Included?	‎No
Batteries Required?	‎No
Color	‎Gold
Customer Reviews	4.2 4.2 out of 5 stars 1,234 ratings 4.2 out of 5 stars
Included Components	‎
Is Discontinued By Manufacturer	‎No
Item model number	‎861
Item Package Quantity	‎1
Item Weight	‎2.94 pounds
Manufacturer	‎General Tools
Material	‎Aluminum
Part Number	‎861
Power Source	‎Hand Powered
Product Dimensions	‎12 x 3 x 3 inches
Size	‎Pack of 1

5 Star

4 Star

3 Star

2 Star

1 Star

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem^*

Twoja ocena

Scritto da: jblues

Not tight, loose actually

After some playing and watching videos plus several test pieces I got it looking nice and nearly flush. I am sure after glue up it will be fine. I like my fits to slightly hold if I turn upside down, friction fit that is. There is about 1/32 -1/64 gap in fitment. The wood will swell, but just not how I like it. I used it in my router table. The instructions are confusing, could be made much simpler. It is not difficult to use once understand the measurement settings. Set router to set the depth of the pins. In other words it sets the depth of the half blind or how proud throughs will go. The depth on the other side is always the thickness of the board. Like others said the plastic portion is it’s weak link. Does not sit flat and the slide gives some. The aluminum is also soft. Don’t over tighten the clamps it will bend. For production style drawers this unit will work fine. If you have a bunch to do it is worth it. If you want to make dove tails for show pieces I would probably look elsewhere. These just aren’t that tight, no way to make it tighter. Also stand a fair chance of being slightly out here and there. I would hate to screw up some nice curly, white oak, walnut or exotic sho

Scritto da: bobby foresta

Simple and accurate

This was really easy to use especially on the router table. I'm only using it or half blind dovetails. I use another simple jig for box joints and I do through dovetails by hand. It took me a few tries to get the bit height and depth of cut (with the depth gauge) just right it was too tight at first but once I adjusted the bit height and depth gauge slightly I got the results I wanted. One thing to know is the inner sides face you as you're routing on the router table. It all aligned well the alignment with the depth gauge fingers make the parts line up top and bottom very well. This is exactly what I hoped.. a repeatable accurate simple way to make half blind dovetails without having to take a college course in jig set up the videos on-line helped a lot and the manual was good

Scritto da: Grigor berberian

Excellent quality, very easy to use, very precise.

Didn't review any product for years, even got many of them, which deserves it. Couldn't pass on this one, because it's such a good quality, solid, very precise, with excellent hard coat finish. Received it just couple of hours ago, adjusted the bit on my router table, watched instructions on you tube couple of times, and did test cuts. If someone whant beautiful looking, tight dovetails, this jig will let you do it in just few minutes, and the price is uncomparable.5 stars all day long and will recomend to anyone.

Scritto da: C. Kelly

Close, but no cigar

As you can see from the attached pictures, the dovetails turn out accurate, but in some cases they’re too tight. You really have to hunt down the correct height of the router bit for them to fit nicely. The misalignment issue you can see in the first two pictures was my fault and was my first attempt. I’m not sure I’ll be able to use this unless the dovetails are hidden as the tear out issue is too great. When making the tails you would need to clamp wood on both sides of your piece to prevent tear out and then you risk the cut piece not being square. I even tried inserting the bit behind the piece to back cut on each tail before going in from the front and still had issues. This was an issue in both hardwood and softwood, but perhaps it’s not as bad on plywood. If you can overcome the shortcomings of this jig, then it’s a great deal as far as setup, form factor and accuracy for the price. I’ll try plywood and update my comment if it’s any better.

Scritto da: Amazon Customer

Not sure yet

Finally got around to trying it out. Supplied bit is not sharp. Was using pine and it struggled--bad. Chipped and broke out the wood. Will have to buy a different bit and try when i have time. If you supply a bit then it should be good enough to do the job. Guess i just ended up with the dull one.

Scritto da: KP

Good design and value. One small defect on the tail side.

IF YOU FOLLOW THEIR INSTRUCTIONS, the jig does a nice job making 1/2" hidden dovetails. I think it was well designed and rather easy to use for the value. Definitely want to do a few practice cuts. I had one issue, i.e., on the tail side, the left and right sides were not exactly level, causing the router not to glide nicely. Starting on the right, about halfway thru when the router hits the left side, I would have to lift up the router slightly. This caused the tails on the left to be slightly shorter than the right (less than 1/16"). When cutting the pins, it was fine. Knowing how it was, I was able to compensate for the unevenness to get nice finished dovetails.

Scritto da: Amazon Customer

Needs work

Great concept for small dovetail joints. Clamps need some work. Clamping bar should be heavier gauge and set screws and knobs should be upgraded. It’s easy to bend/twist the clamping bar which will lead to improper alignment and weak hold.

Scritto da: Kyle McCans

Jig is fine. But is trash.

Jig is a jig. It’s aluminum so if you nick it with the router it’s taking a chunk out. The bit that comes with is basically useless. Dull and could hardly use it for a test piece.

Scritto da: lee

Jig

Outstanding value for money

Scritto da: David Child

Good value

Good piece of kit, just set up with 2 bits of scrap first and your ready to go

Scritto da: Tormod

Be careful

As with all these gadgets, careful setup and measuring is key. Makes very nice looking blind dovetails if care is taken. One other thing to note is that you should be very careful when tightening the clamps on your work piece as it will push the whole jig out of shape and throw your router out. This tool could be improved by strengthening the structure and with more reference markings on the guides.

Scritto da: Amazon Customer

Good product but needs improving .

If you clamp too tightly the jig distorts and makes Joints sloppy and out of line. Will be buying the trend jig soon .

Scritto da: Amazon Customer

Second hand tool

I bought this product to cut dovetails on drawers that I am making for my daughter, I've not used the jig yet, but it looks like somebody has already used this jig before me. I didn't think for one minute that I would be receiving a secondhand product, as soon as I opened the bag that it was delivered in I noticed that the the packaging had been opened, the jig was covered in fine sawdust and there are some Nick's in the fingers where the cutter has caught the jig, probably by the previous owner removing the router whilst in motion, there is also track Mark's around the fingers where the bearing of the cutter has been in contact. I am not a happy customer at this moment in time.