Elektryczna rozlutownica Jameco Benchpro do usuwania lutów, 30 W, 60 Hz, 120 V AC, przyssawka lutownicza — SA6-R

Brand:JAMECO BENCHPRO

3.4/5

306.42

Jak korzystać z pompki do rozlutowywania Krok 1: Naciśnij tłok, aż zostanie zablokowany i usłyszysz kliknięcie; Krok 2: Przyłóż końcówkę lutownicy do złącza lutowniczego i pozwól, aby lut stał się w pełni płynny; Krok 3: Przesuń końcówkę pompy obok stopionego lutu. Odsuń żelazko na bok i natychmiast przykryj kałużę płynnego lutu końcówką pompki. Pociągnąć za spust; Krok 4: W razie potrzeby powtórz ten proces.

Brak dostępnych jednostek
Służy do poprawiania błędów z małymi płytkami na PCB, ponownego lutowania mechanicznych przełączników klawiatury, usuwania przekaźników i innych elementów z płytek drukowanych, rozlutowywania starych przewodów, rozlutowywania części komputerowych, takich jak płyty główne, czyszczenia stopu elementów smd i innych. Leży płasko: gdy nie jest używana lub pomiędzy zadaniami, pompa rozlutowująca leży płasko z uniesioną gorącą końcówką, aby zapobiec niepożądanym poparzeniom. Łatwa obsługa: Zaprojektowany do obsługi prawą lub lewą ręką. Szybko się nagrzewa i wykorzystuje mocną pompę próżniową do usuwania lutu. 30 W: Wystarczająco mocna, aby usunąć typowe błędy lutowania występujące w małych urządzeniach. Szybko się nagrzewa.
Batteries Required? ‎No
Customer Reviews 4.4 4.4 out of 5 stars 104 ratings 4.4 out of 5 stars
Included Components ‎1
Item model number ‎SA6-R
Item Package Quantity ‎1
Item Weight ‎7.4 ounces
Manufacturer ‎Jameco Benchpro
Package Dimensions ‎14.17 x 8.5 x 1.22 inches
Part Number ‎SA6-R

3.4

8 Review
5 Star
64
4 Star
23
3 Star
4
2 Star
6
1 Star
4

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: bMin
Third of a Century later, this is still great.
I bought this one from Jameco in the '80s I get more to gift whenever it's on sale. If you swab the metal crumbs out and silicone grease the seal ring gasket on the piston and tip, it pulls like new again.
Scritto da: Brian S. Kokernak
"holy crap it worked"
I said that out loud after I used it. (And my language was a little more colorful.) Anyway, I am TERRIBLE at desoldering. I usually end up making the problem worse or completely destroying the board. Well not anymore... it very cleanly removed all the solder from some pot sliders, and with some needle nose pliers, I was able to yank it off the board with minimal effort. I wish I bought one of these years ago.
Scritto da: Blipblox by Playtime Engineering
Makes the job easier
I've been soldering for 30 years, and removing solder from through-holes is always difficult. Even using that nice $250 tool with the built-in vacuum (which I have) , it is still really difficult. The absolute worst is trying to wick solder out of a through hole, it never works, and is very frustrating. This tool makes it a little easier. It isn't an instant miracle worker, but if you stay at it, you can get that solder out of the hole. See my two photos of an 8 pin through-hole component where I was able to use this tool to remove the solder. Still took me about 15 minutes. I really wish this iron had an auto shut-off, and the sucking mechanism is pretty weak. However, for the price, this tool is completely worth it as I had no other options for removing solder from these through-holes. Recommended.
Scritto da: kevin
Pleasantly surprised!
This little powerhouse is an essential tool for my home repairs.. it can do the work of a higher priced desolder for a fraction of the price.. the only difference is it will take a little more time to manually compress the pump.. definitely recommend!
Scritto da: R. Westcott
Excellent. Convenient one-handed operation.
So far so good. Seems well designed. Hope it keeps working as good as it did for my 1st project.
Scritto da: Whodiini
much better than just a pump
So I have been a hobbyist for a long time. Desoldering components is a pain. So what are the choices? 1) Use a hand vacuum pump. This has never worked well for me, esp these more modern circuit boards. Heat up the component and hit it with a pump - by the time you do that, the solder has resolidified. 2) Wick and flux. This never worked for me until I learned you need to use solder flux as well. dip the wick into the flux (or put a drop on the wick). Most often works. But you need to clean the burnt flux afterwards. Also takes time,. 3) Solder pump/gun. The vacuum ones cost about $250. So I decided to get this to try how it works. Vacuum is mediocre. Takes about 4 tries to get the solder off and then still have to pull the heated component out. Doesnt just drop off. But this is faster and leaves open holes in the board. So this is much better than wick and flux. For someone who uses this several times a year, this is the most cost effective option. Oh, BTW, the first time, heat it outside for 20 min to burn off whatever it is that smells.
Scritto da: Johan Bach
GAME CHANGER!!!
must have for mechanical keyboard enthusiasts works amazingly well, but frequent maintenance is a must!!!! usually needs to be cleaned after desoldering 1 keyboard
Scritto da: Amazon Customer
It did the job
Worked as described i depinned a 10 pin relay

Produkty powiązane

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array