Czujnik wycieku wody D-Link Wi-Fi i zestaw startowy alarmu, cały system domowy z powiadomieniem z aplikacji, zasilanie prądem przemiennym, nie wymaga koncentratora (DCH-S1621KT) Zestaw czujnika wody V2

Name: Czujnik wycieku wody D-Link Wi-Fi i zestaw startowy alarmu, cały system domowy z powiadomieniem z aplikacji, zasilanie prądem przemiennym, nie wymaga koncentratora (DCH-S1621KT) Zestaw czujnika wody V2
Brand: D-Link
SKU: 0790069460999
Price: 477.21 PLN
Availability: InStock

Brand:D-Link

3.3/5

zł
477.21

Zestaw startowy czujnika wycieku wody to łatwe w użyciu domowe rozwiązanie do samodzielnego wykrywania nieszczelności, które powiadamia o wszelkich wyciekach wody natychmiast po ich wystąpieniu, dzięki czemu można uniknąć kosztownych napraw uszkodzeń spowodowanych przez niewykryte wycieki. Zestaw zawiera jednostkę główną (lub koncentrator) z dołączanym kablem czujnikowym oraz zasilaną bateryjnie kapsułę czujnikową. Koncentrator można podłączyć do dowolnego gniazdka ściennego, a czujnik można umieścić w miejscach narażonych na wycieki wody, takich jak pralka, podgrzewacz wody, pod zlewem. Pod ma dwie fabrycznie zainstalowane baterie AAA, które zapewniają do 5 lat pracy na baterii. Oba urządzenia są bardzo łatwe w konfiguracji i są wstępnie sparowane z aplikacją mydlink, którą można pobrać na smartfon i łatwo połączyć z istniejącym domowym Wi-Fi. System wielu ostrzeżeń (dźwiękowy, wizualny, mobilny) sprawia, że jest dostępny w domu lub poza nim. Światło stroboskopowe LED koncentratora zapewnia wizualne powiadomienie, a wbudowany alarm o natężeniu 100 dB jest łatwo słyszalny. Możesz także połączyć się z głośnikiem Google, aby otrzymywać powiadomienia głosowe, a na telefon komórkowy wysyłane są rozbudowane powiadomienia. Skalowalny i wszechstronny, możesz dodać do 16 kapsuł w całym domu. Niskoprofilowa konstrukcja Pods ułatwia dyskretne umieszczanie, a kabel czujnikowy pozwala na umieszczenie większej ilości poza zasięgiem. Niezawodny zestaw czujnika wody mydlink jest zawsze włączony, więc kiedy jesteś poza domem, masz spokój ducha.

Kwota

Dodaj do koszyka Kup Teraz

EAN: 0790069460999

Kategorie Narzędzia i ulepszenia domu, Bezpieczeństwo i ochrona, Domowe czujniki i alarmy, Detektory i alarmy wody,

Niekompatybilny z DCH-161-US (wersja zasilana bateryjnie). Czujniki wykorzystują pasmo sub-gigahercowe, aby zapewnić większy zasięg i łączność w obszarach, do których Wi-Fi nie może przeniknąć, takich jak piwnica. Master Sensor podłącza się do gniazdka ściennego i łączy z domowym Wi-Fi. Zdalne czujniki są zasilane dwiema bateriami AAA (w zestawie) o żywotności do pięciu lat. Łatwa konfiguracja i umieszczenie: Master Sensor Plug wykorzystuje 5-metrowy przewód z dołączanym 1,5-metrowym kablem wykrywającym wodę. Bezprzewodowo rozszerz zasięg nawet w 16 wrażliwych obszarach, takich jak podgrzewacze wody, pralki i pod zlewami, za pomocą uchwytów na czujniki (DCH-S163). Alerty obejmują potężne światło stroboskopowe LED, wbudowany alarm 100 dB, powiadomienia z telefonu komórkowego i alerty głosowe z głośnikami Google, które zapewniają powiadomienia w czasie rzeczywistym, gdziekolwiek jesteś. Unikaj kosztownych uszkodzeń spowodowanych przez wodę: Master Sensor Plug-in z kompaktowym, wodoodpornym uchwytem Sensor Pod (DCH-S163) wykrywa wycieki; system multi-alert (głos, alarm, tekst) powiadomi Cię od razu.

Batteries	2 AAA batteries required.
Brand	D-Link
Color	White
Country of Origin	China
Customer Reviews	4.2 4.2 out of 5 stars 209 ratings 4.2 out of 5 stars
Item Dimensions LxWxH	2.25 x 2.32 x 2.19 inches
Item model number	DCH-S1621KT
Item Weight	5.1 ounces
Manufacturer	D-Link Systems, Inc.
Number of Batteries	2 AAA batteries required.
Number of Batteries	2 AAA batteries required. (included)
Power Source	Battery Powered
Product Dimensions	2.25 x 2.32 x 2.19 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem^*

Twoja ocena

Scritto da: Wesley Dean

detects water but the notifications are irregular; won't talk to Home Assistant

When the probe gets wet, it triggers the alarm as-expected. However, the period between state changes (e.g., going from wet to dry or dry to wet) is way, way, way too short. As a result, when the probe gets wet, it vacillates between wet and dry multiple times per second and each time resulting in a notification being generated. That is, the alarm chirps in an almost strobe-like manner and my phone "blows up" with multiple notifications per second. I'm extremely reluctant to configure a "designated contact" with a phone number. I understand that the contact is notified when a button is tapped on the notification (i.e., it's not automatic), I don't trust the app to stay within its walled garden. The wired device (DCH-S162) supports integration with Alexa and Google Assistant. This is configured via the MyDlink app. This leads me to believe that there is some kind of API or MQTT support by which the device communicates; however, there is not (yet) support for Home Assistant. There is support for the DCH-S160 via 3rd party integration; however, that integration doesn't support the DCH-S161. Moreover, the product listing asserts that this device is not compatible with the DCH-S161 which leads me to believe that there is yet another variation in communication mechanisms. (i.e., if Home Assistant supported the DCH-S161 and this device was compatible with DCH-S161s, it may be possible to get Home Assistant to talk to it). If the device was supported by Home Assistant, one could trigger notification upon continued state of water detection *for more than 5 seconds* to resolve the aforementioned notification issue; similarly, it could be used to trigger a secondary pump to run. But it doesn't, so I can't. If I were to do this project over again, I would likely go with a SOC device (e.g., a Raspberry Pi) that I could control; however, for a typical consumer, I suspect that this device would be sufficient.

Scritto da: P. Koskiniemi

Easy set up. Excellent customer support!

I read the reviews of people having trouble pushing the set buttons on the back of the sensors when pairing. The easiest solution is to push the button firmly with the rounded end of a ball point pen cap for about 2-3 seconds and you will get the light! The setup and pairing are very easy. Be advised that you must have a smart phone for set up and that the notifications are limited to push notifications through the mydlink app. No text, email, or phone notifications are available. All things considered this product is very reasonably priced and the sensors work well. The sensors are small enough to fit under your dishwasher and refrigerator, and the cable sensor is perfect for going under the washing machine.

Scritto da: Iainsmith

A Very Disappointing Product

I read a review in a trusted New York newspaper that rated the d-Link DCH 162 hub and DCH 163 water leak sensors very highly. I needed water leak protection so I bought the package on Amazon and subsequently purchased a 3-pack of sensors from d-Link (not available through Amazon). The first problem I noticed was how difficult it is to put the sensors into pairing mode. You have to stand close to the hub and press the pairing button on the bottom of the sensor with all the finger strength you have. I paired 4 sensors and they were all tough to activate. The mobile app walks you through the set up, which is pretty easy. I changed the system-generated sensor ID to the locations of where the sensors were placed. For example DCH-S163-0E48 was changed to 3rd floor bathroom. Unfortunately the app still shows the original number instead of the label on 2 of my 4 devices. If I drill into the device details it shows “3rd floor bathroom” but not on the home page where I need it. The labels seem to change around so I suspect it’s a bug in their software. Last week one of my devices displayed in the mobile app as off-line. The device had been placed behind a stacked washer / dryer and wasn’t accessible without moving the machines. When I drilled into the detail of the device from the Home Screen of the mobile app the status showed as being in power-save mode. I called d-Link support and was told not to worry about the off-line status on the Home Screen. I was assured that it would still sound an alarm if water were detected. I was not convinced since the other 3 sensors showed as being in power-save mode from the Home Screen. I eventually moved the machines, removed the device through the app and set it up again. It now shows correctly as being in power-save mode. When I first set up the hub I enabled notifications and ran the recommended water test and after an initial notification failure re-ran the test was notified on my phone of a water leak. This was great except when our water actually leaked under the kitchen sink today and I was out of the house I didn’t receive a notification . I did, however, receive a frantic call from my wife about water pouring onto the kitchen floor. I could hear the alarm in the background (very loud). When the alarm first sounded she ran upstairs thinking we had a leak under the washing machine only to discover it was in the kitchen when she came back downstairs. She asked why the system didn't tell us the location of the leak; good question. I’m hoping my experience with this system improves. Right now I have little confidence in either their mobile app or support. I’m disappointed in d-Link.

Scritto da: Horn player

Make sure you test it and the app.

Pleased with it. It would be good if the email message would trigger an alarm on the phone. It is easy to miss the email. Maybe the email notificaton could trigger a ring tone, like a fire alarm. I tried to figure out how to do it without success. That would be a great feature. If anyone out there can figure out who to do that, I would like to know. Thanks.