Rain Bird 12DSH Podwójna dysza zraszająca, 180° półokrągły strumień, 9' - 12' odległość zraszacza półokręg 180° wzór półokrągły 180°

Brand:Rain Bird

3.7/5

104.76

OPIS PRODUKTU Rain Bird 12DSH Podwójny zraszacz Półokrągły strumień 180° Dysza o dopasowanej dawce opadu, regulowana odległość zraszania od 9' do 12', trajektoria 23°. Ta specjalna dysza ma dwa otwory zraszające, które zapewniają lepsze podlewanie z bliska i bardziej równomierną dystrybucję wody. Unikalna opatentowana konstrukcja podcięcia skraca czas nawadniania, zużywa o 30% mniej wody i zmniejsza straty wody w wietrznych warunkach. Obszary blisko głowy otrzymują równomierne pokrycie, minimalizując suche brązowe plamy. Odporna na korozję konstrukcja z tworzywa sztucznego i stali nierdzewnej zapewnia długą żywotność. śruba regulacyjna ze stali nierdzewnej reguluje natężenie przepływu od 1,8 do 2,6 galonów na minutę i odległość natrysku od 9 'do 12'. Uchwycony otwór na śrubę zapobiega ślizganiu się śrubokręta podczas regulacji. Dysza rozpyla półkola o kącie 180° z trajektorią 23° i pasuje do wszystkich zraszaczy Rain Bird i adapterów do krzewów. Sito filtra o drobnych oczkach zapewnia precyzyjną regulację promienia i chroni dolny otwór przed zanieczyszczeniami. Dysze Rain Bird MPR, cieszące się zaufaniem od dziesięcioleci, są wyposażone w technologię dystrybucji wody o dopasowanej dawce opadu. Dysze o różnych łukach i promieniach można mieszać w tej samej strefie niezależnie od regulacji strumienia i nadal utrzymywać równomierne rozprowadzanie wody. Dostępny jest szeroki wybór dysz MPR, dzięki czemu dystrybucję wody można dostosować do unikalnych i różnorodnych potrzeb Twojego krajobrazu. Dysze MPR zostały zaprojektowane tak, aby zapewnić równomierne pokrycie, dzięki czemu trawnik jest cały zielony, bez suchych lub brązowych plam. Inne dostępne dysze Dual Spray MPR (sprzedawane oddzielnie) to: 360° pełny (12DSF) i 90° ćwierćdolarowy (12DSQ). Rain Bird „Inteligentne wykorzystanie wody OD PRODUCENTA Rain Bird Corporation to prywatna firma założona w 1933 r. podczas boomu rolniczego w Kalifornii. Jesteśmy uznawani za producenta nr 1 i dostawcę produktów i usług związanych z nawadnianiem na świecie. Z biurami sprzedaży na całym świecie; oferujemy ponad 4000 wodooszczędnych produktów do nawadniania w ponad 130 krajach. Od samego początku firma Rain Bird produkowała i oferowała najszerszą w branży gamę wysokiej jakości produktów do nawadniania dla: gospodarstw rolnych, pól golfowych, aren sportowych, obiektów komercyjnych i domów. W ciągu ostatnich 80 lat firma Rain Bird uzyskała ponad 450 patentów na całym świecie. W tym pierwszy do nawadniania w 1935 roku na naszym oryginalnym zraszaczu z napędem udarowym (patent USA nr 1 997 901), który zrewolucjonizował rolniczą produkcję żywności i zapoczątkował nową erę w nawadnianiu na całym świecie. W 1990 roku ten oryginalny zraszacz uderzeniowy został uznany za historyczny punkt orientacyjny przez Amerykańskie Stowarzyszenie Inżynierów Rolnictwa. Nasze produkty obejmują wszystkie aspekty nawadniania… zegary/kontrolery, zraszacze rotacyjne wynurzalne, zraszacze wynurzalne, dysze zraszaczy, zawory irygacyjne, nawadnianie kropelkowe, drenaż i wiele innych. Produkty te zostały wybrane i zainstalowane na całym świecie w największych i najbardziej prestiżowych projektach nawadniania budynków mieszkalnych, komercyjnych, rolniczych i pól golfowych. Rain Bird angażuje się w Inteligentne wykorzystanie wody™ wykraczające poza produkty na edukację, szkolenia i usługi dla przemysłu i społeczności. Naszym dziedzictwem jest projektowanie i wytwarzanie wyłącznie produktów o najwyższej wartości i jakości. Jesteśmy wdzięczni za otrzymanie licznych nagród uznania od wielu naszych cenionych partnerów. Rain Bird „Inteligentne wykorzystanie wody

Zbudowany z bardzo trwałych materiałów odpornych na promieniowanie UV i chemikalia, aby zapewnić długą żywotność. Śruba regulacyjna ze stali nierdzewnej reguluje natężenie przepływu i odległość natrysku. Eliminuje suche brązowe plamy w pobliżu głowy. Kompatybilny ze wszystkimi zraszaczami wynurzającymi Rain Bird. Wzór półkola 180° z regulowaną odległością natrysku od 9' do 12'. zużywa o 30% mniej wody; zmniejsza straty wody w wietrznych warunkach. Podwójne dysze zraszające zapewniają doskonałe podlewanie z bliska.
Brand Rain Bird
Color Brown/Black
Country of Origin USA
Customer Reviews 4.7 4.7 out of 5 stars 276 ratings 4.7 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 0.89 x 0.89 x 2.1 inches
Item model number 12DSH
Item Weight 0.022 ounces
Manufacturer Rain Bird
Material Stainless Steel
Product Dimensions 0.89 x 0.89 x 2.1 inches
Style Pop-Up

3.7

7 Review
5 Star
75
4 Star
20
3 Star
3
2 Star
0
1 Star
2

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: Eugene
Better near and far spray coverage
To adjust the spray distance and water output of this nozzle, turn the screw on top counterclockwise for an increase, or turn it clockwise for a decrease. To adjust which direction it sprays, you can remove the top of the sprinkler head and reinsert the nozzle tube. Some sprinkler heads are installed deep enough that pulling the top off is undesirable, so you can pull up the nozzle tube and twist it until it's rotated in the right direction. It should make clicking noises as it is turned. If there's no clicking, then you may be unscrewing the sprinkler from the pipe beneath it, or unscrewing the top of the sprinkler, so I prefer to turn it clockwise. I use this nozzle wherever I don't need an adjustable nozzle because it does a better job of providing even coverage both near and far. It works great wherever my sprinklers pop up high enough, which in my lawn requires at least a 4 inch sprinkler. I have a couple 2 inch sprinklers that don't come up enough, so the dual spray part of this nozzle sprays directly into the grass right next to it. It's not the fault of the nozzle, but a notification that I should swap out that sprinkler head. I've also found that this nozzle can directly replace some of the nozzles on my Orbit sprinklers. My only gripe with this nozzle, and all Rain Bird nozzles, is that the adjustment screw tightness has a lot of variation. Sometimes it's so tight that the nozzle must be pulled up and gripped tightly to adjust it, which results in a face full of water if you try this while the sprinklers are on, but other nozzles are loose enough that they can be adjusted just by turning the screw without holding onto the nozzle. Fortunately giving the adjustment screw a few turns to loosen it up before installing it is all it takes to resolve this minor issue.
Scritto da: Eugene
Good near and far spray coverage
To adjust the spray distance and water output of this nozzle, turn the screw on top counterclockwise for an increase, or turn it clockwise for a decrease. To adjust which direction it sprays, you can remove the top of the sprinkler head and reinsert the nozzle tube. Some sprinkler heads are installed deep enough that pulling the top off is undesirable, so you can pull up the nozzle tube and twist it until it's rotated in the right direction. It should make clicking noises as it is turned. If there's no clicking, then you may be unscrewing the sprinkler from the pipe beneath it, or unscrewing the top of the sprinkler, so I prefer to turn it clockwise. I use this nozzle wherever I don't need an adjustable nozzle because it does a better job of providing even coverage both near and far. It works great wherever my sprinklers pop up high enough, which in my lawn requires at least a 4 inch sprinkler. I have a couple 2 inch sprinklers that don't come up enough, so the dual spray part of this nozzle sprays directly into the grass right next to it. It's not the fault of the nozzle, but a notification that I should swap out that sprinkler head. I've also found that this nozzle can directly replace some of the nozzles on my Orbit sprinklers. My only gripe with this nozzle, and all Rain Bird nozzles, is that the adjustment screw tightness has a lot of variation. Sometimes it's so tight that the nozzle must be pulled up and gripped tightly to adjust it, which results in a face full of water if you try this while the sprinklers are on, but other nozzles are loose enough that they can be adjusted just by turning the screw without holding onto the nozzle. Fortunately giving the adjustment screw a few turns to loosen it up before installing it is all it takes to resolve this minor issue.
Scritto da: Dazzza
Great Replacement at Low Cost
These nozzles fit the 1800 series and UNI-Spray series sprinkler head bodies. They will also fit onto most other brands of sprinklers that use universal female thread nozzles. While Rainbird makes a wide range of nozzles, most are only available at specialty irrigation stores. Hardware stores and home centers tend to only carry a few of the most common nozzles. Rainbird makes a very good nozzle set with good water spray uniformity. Many of them have matched precipitation rates so you can mix different radius and pattern nozzles on the same valve zone without messing up the water application uniformity. Be careful of this as Rainbird's literature calls all of their nozzles "matched precipitation rate", but that does not mean they are all compatible with each other! For example, you should not use a 4 series VAN nozzle on the same valve circuit as a 5 series MPR nozzle. Read the nozzle descriptions for each series of nozzles below for details on which nozzles are compatible. The spray radius can be reduced up to 25% on all but a few specialty bubbler nozzles using a screw on top of the nozzle. Note that the separate screen must be installed under the nozzle for the radius adjustment to work correctly. If you remove or don't install the screen you won't be able to adjust the radius. The screens are provided with the nozzles when you purchase them. All Rainbird nozzles are constructed of high-quality plastic.
Scritto da: Padmapada
Easy fix for a damaged sprinkler head, saved lots of $$$
The folks who cut my grass tend to cut the heads off the sprinklers with their machines. In the past, I've called the sprinkler company to fix them, and ended up paying hefty service calls. This time I had a look and saw that the damaged head simply unscrewed. So I went to the local big box store and tried to find a replacement. The clerk tried to talk me into buying something that had threads on the OUTSIDE because, I guess, that is what he had in stock. But I needed a head with threads on the inside, one that would just screw down on top of the pop-up pipe. I saw this on Amazon and asked other customers if it had threads on the inside, and the answer was positive. So I bought this, and it took about 2 minutes to install. The head is clearly marked so that you can see which way the spray goes (this is a half circle), and there is a screw on top to reduce the diameter if you want. It is installed in the berm, or tree lawn, or verge, or curb strip, or whatever you call that narrow strip of lawn between the sidewalk and the street. Perfect. Good for all dialects.
Scritto da: Cindy
Good product
Product fit as described
Scritto da: Amazon Customer
Performance met the product description.
Did a lot better than the water savors you can buy.
Scritto da: Brenda Brennan
Perfect fit
Perfect to replace broken sprinkler head.

Produkty powiązane

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array