LMT Onsrud 63-768 węglik spiekany Upcut Spiral O rowek, calowy, niepowlekane (jasne) wykończenie, kąt linii śrubowej 21 stopni, 1 rowek, długość całkowita 2,0000, średnica skrawania 0,1875, średnica trzonka 0,2500 3/16 cala

Brand:LMT Onsrud

2.8/5

343.52

OPIS PRODUKTU Greenlee z dumą zatrudnia pracowników w Stanach Zjednoczonych w siedmiu zakładach produkcyjnych, w których projektujemy, montujemy i wytwarzamy określone produkty, które spełniają rygorystyczne wymagania dotyczące produkcji w USA lub kwalifikacyjne. Zachęcamy konsumentów do zapoznania się z opakowaniami naszych produktów lub materiałami marketingowymi znajdującymi się na stronie greenlee, aby zrozumieć pochodzenie poszczególnych produktów. OD PRODUCENTA Multimetr cyfrowy Greenlee DM-200 600 V jest wyposażony w funkcję automatycznego ustawiania zakresu dla wygodnej obsługi, bezdotykowego wykrywania napięcia i oszczędzania czasu. Pomiary zatrzymania i przechwytywania danych. Automatyczne wyłączanie i wskaźnik niskiego poziomu baterii. Obsługuje RS-232, może być podłączony do komputera PC w celu uzyskania rozszerzonych możliwości pomiarowych z optycznie izolowanym interfejsem DMSC-2. Tryb wyświetlania względnego przesunięcia, aby zobaczyć względne zmiany w pomiarach. Pomiary częstotliwości, temperatury i pojemności oraz cykl pracy AC. Akcesoria obejmowały dwie baterie 1,5 V AAA, przewody pomiarowe i czujnik temperatury kulek. Maksymalnie 6000 pomiarów napięcia.

Brak dostępnych jednostek
Pojedynczy rowek, kąt 21 stopni. Podczas pracy w kierunku przeciwnym do ruchu wskazówek zegara (cięcie w prawo) spiralne narzędzia rowkowane odprowadzają wióry w górę i na zewnątrz cięcia, aby zmniejszyć zatykanie. Okrągłe chwyty umożliwiają stosowanie z szeroką gamą systemów mocowania narzędzi. Narzędzia niepowlekane zawierają tylko podłoże podstawowe bez dodatkowej obróbki lub powłok i nadają się do szerokiego zakresu zastosowań. Narzędzia pełnowęglikowe zapewniają długą żywotność narzędzia i większą prędkość skrawania niż inne podłoża, ale są bardziej kruche i muszą być używane ze sztywnymi systemami mocowania narzędzi.
Country of Origin USA
Cutting Diameter 0.19 Inches
Cutting Length 0.63 Inches
Domestic Shipping Item can be shipped within U.S.
Finish Type Uncoated
Finish Type Uncoated (Bright)
International Shipping This item can be shipped to select countries outside of the U.S.
Item model number 63-768
Manufacturer LMT Onsrud
Material Carbide
Number of Flutes 1
Product Dimensions 4 x 0.5 x 0.5 inches; 0.8 Ounces

2.8

8 Review
5 Star
47
4 Star
18
3 Star
10
2 Star
9
1 Star
16

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: R. A. Jones
Nice cutter, shank is 1/4" despite the title and photo.
The title is a bit off because it says the shank is 0.125" when the specs say the shank is 1/4". The photo also shows a cutter with the shank diameter the same as the cutting diameter. It IS, however, 1/4" shank. I use it on a smallish CNC router with a 2hp spindle and it's worked quite well. In soft plastics like ABS I initially had the chip winding around the shank, melting and make a truly horrible cut. I built a new dust shoe to dramatically increase the air velocity around the cutter and with that dust shoe to keep the chips clear this cutter has worked very well.
Scritto da: Mississippi
Good bit
Nothing wrong with this one
Scritto da: Paul Haiducu
Arrived damaged!
I am not an expert in this, but the shop teacher I have worked with to drill holes in an aluminum plate tells me that the bit is damaged and cannot be used. Unfortunately, we have not carefully looked at the bit when it arrived (ordered on May 23, 2019), hence it is too late to return it or exchange it. It took the teacher a while to find time for the project I wanted done (we had the summer off, traveling, etc.). Yesterday, he realized that the bit is no good. The bit has not been used (and the shop teacher tells me that is obvious). These are not cheap, I am out almost $30.
Scritto da: Andrew D. Mowry
The description for this is incorrect. The 1/8” bit ...
The description for this is incorrect. The 1/8” bit has a 1/4” shank, not 1/8” as described and shown in the photo.
Scritto da: Seein Stripes
Great for HDPE on Bob's CNC E3
I now have about 20+ hours on the bit cutting and drilling .375" Starboard HDPE. I can say it is RAZOR sharp since it sliced my finger like a scalpel trying to remove some plastic shavings from around the bit. Runs straight and true at 45 ipm on my Bob's CNC machine.
Scritto da: Gary
This is the best bit I ever used on this material
I cut an aluminum composite material with this bit. The material is 2 aluminum skins bonded to a plastic center. This is the best bit I ever used on this material, a very clean, effortless cut.
Scritto da: Eric Varsanyi
Great cutter, clean edges on acrylic
This cuts acrylic like butter and leaves a very nice edge. I'm running a router at 18000 RPM with a feed rate of around 70 IPM and .06 depth cuts in cast acrylic.
Scritto da: bookbound93
Not 1/8 shank
Nice cutter, but needed a 1/8 shank and this is a 1/4 shank. Not happy.

Produkty powiązane

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array