Flair-It Sales 10800 Plastikowa podpórka pod zginanie, rozmiar 0,5 cala

Brand:FLAIR-IT SALES

3.5/5

127.11

Oferujemy największy wybór produktów hydraulicznych PEX. Mamy rozwiązania dla każdej potrzeby hydraulicznej PEX! Nazwij to, mamy to. Wyposażony w całkowicie nowy system hydrauliczny PEXLOCK, który wykorzystuje wyłącznie narzędzia domowe. Wszystko dla PEX, w tym pierścienie zaciskane PEX ze stali nierdzewnej i miedzi PEX. Złączki zaciskane PEX z tworzywa sztucznego Ecopoly, złączki Flair-It PEX i polibutylenowe, kolektory Flair-It PEX, produkty instalacyjne PEX, rurki PEX do ogrzewania promieniującego, rurki pert, rurki safepex (PEX a), najlepsze rurki PEX (PEX B), rury PEX, Obcinaki do rur PEX, zaciskarki PEX, serwisowe zestawy naprawcze PEX i ekspozycje sklepowe PEX.

Numer części: 10800. Kraj pochodzenia : Chiny. Waga paczki: 1 funt. Wymiary opakowania: 5,5 dł. x 3,25 wys. x 1,0 szer. (cale).
Brand FLAIR-IT SALES
Color Copper
Country of Origin China
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Stainless Steel
International Shipping This item can be shipped to select countries outside of the U.S.
Item model number 10800
Manufacturer FLAIR-IT SALES
Material Plastic
Number of Pieces 1
Package Dimensions 5.39 x 2.52 x 0.87 inches; 0.63 Ounces
Size 0.5
Thread Size 0.5 inch

3.5

9 Review
5 Star
61
4 Star
21
3 Star
19
2 Star
0
1 Star
0

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: Amazon Customer
Works as expected
Perfect for bending PEX. Great product and better than splicing to get the angle.
Scritto da: C. Anderson
Work and affordable but Sharp and too much packaging
The per piece packaging is annoying. It was better when then were 10 piece. Price is better than box stores. They are sharp, as others stated, but this did not affect the Pex. Have not had a problem with the lines popping out of the bend support, but lines have only been pressurized with air so far.
Scritto da: T. Davidson
Sharp flashing from mold cuts into your hands when bending PEX into these
The manufacturing injection mold leaves sharp edges that will cut into your hands, wear heavy gloves when working with these.
Scritto da: AlexCphoto
Work great
These work great, not only save you from adding two additional failure points to your lines with additional crimps for a 90deg L but also saves you a bit of $ and time / effort. Takes a bit of strength to use but so does crimping.
Scritto da: Jonathan Wieder
Kind of like a mound was only 90% filled with plastic
The ones I received were black. They seemed to be mis-cast, as the lip that receives the zip tie was only partially there. Kind of like a mound was only 90% filled with plastic. Didn't really affect the usability. Would buy again.
Scritto da: frankievis52
Nice Quality.
Great product for the price. Used it for Plex tubing and it worked great.
Scritto da: lee westmoreland
Not available in big box stores
The metal version of this is available in big box stores locally but the cost is about 3 times more than these. So far, so good - they seem to work very well.
Scritto da: Banned for honest reviews
They may do the job, just be careful that they don't slash your hand open when you install them.
These are fine for the job, but be careful handling them, since they are very poorly molded. The "flash" at the mold seam is bad enough that it can easily cut your hands up. They seem to me to be manufacturer's rejects. No normal retailer would accept these in to their inventory.
Scritto da: Amazon Customer
Works well
This piece works well. It comes with a few rough edges but with a file, some sandpaper and a couple of minutes they were all gone. No worries about kinking the pipe with this and it gives you a way to secure the pipe to the wall or ceiling.

Produkty powiązane

hot
Emberglo 458550 8 1/4 Barbriq 5 szt
4.1/5

zł 563.57

Emberglo 458550 8 1/4 Barbriq 5 szt
4.1/5

zł 563.57

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array