CURT 56189 Niestandardowa 4-pinowa wiązka przewodów przyczepy po stronie pojazdu, pasuje do wybranych Mitsubishi Outlander, czarna

Brand:CURT

3.4/5

427.29

Jeśli Twój pojazd nie jest wyposażony w okablowanie do holowania przyczepy, idealnym rozwiązaniem jest niestandardowe okablowanie CURT. Niestandardowa wiązka przewodów — zwana także trójnikiem — to proste urządzenie elektryczne typu plug-and-play, które podłącza się do samochodowego układu elektrycznego i zapewnia standardowe, uniwersalne połączenie przewodów przyczepy. Odbywa się to za pomocą dwóch lub więcej złączy kompatybilnych z pojazdami OEM, które można podłączyć do zespołu tylnego światła, eliminując potrzebę cięcia, łączenia i lutowania podczas instalacji. Niestandardowe wiązki przewodów są dostosowane do konkretnego pojazdu i chociaż nie są dostępne dla wszystkich pojazdów, oferują jeden z najszybszych, najłatwiejszych i najbezpieczniejszych sposobów okablowania pojazdu do holowania. Ta szczególna wiązka wtyczek zapewnia 4-kierunkowe płaskie złącze i została zaprojektowana jako niestandardowa wiązka przewodów pasująca do niektórych lat Mitsubishi Outlander (aby sprawdzić kompatybilność pojazdu, zobacz informacje o zastosowaniu). Jest dostarczany ze wszystkimi niezbędnymi elementami okablowania do ustanowienia niezawodnego połączenia okablowania przyczepy, a także osłoną przeciwpyłową, która utrzymuje złącze w czystości, gdy nie jest używane. Masz przed oczami obraz swojego następnego miejsca docelowego — może to być łódź przybijająca do twojego ulubionego łowiska, może kemping z widokiem na jedno z arcydzieł natury, a może kolejny duży plac budowy. Jednak przekształcenie tego obrazu w rzeczywistość wymaga czegoś więcej niż tylko marzeń. Wymaga solidnego połączenia i odpowiedniej mocy. Niestandardowe okablowanie CURT jest wykonane przy użyciu jednej z najbardziej zaawansowanych technologii w branży i zostało zaprojektowane z myślą o łatwej instalacji, zapewniając trwałe połączenie elektryczne dla konfiguracji haka holowniczego.

OKŁADKA OCHRONNA. Aby zapewnić długotrwałe użytkowanie i odporność na warunki atmosferyczne, ta 4-biegunowa wiązka przewodów oświetlenia przyczepy jest wyposażona w gumową osłonę przeciwpyłową. Łatwo pasuje do 4-kierunkowego płaskiego złącza, gdy nie jest używany, chroniąc go przed czynnikami zewnętrznymi. NIEZAWODNA MOC. Ta 4-kierunkowa wiązka przewodów przyczepy jest zbudowana w technologii montażu powierzchniowego. Ten typ obwodów elektrycznych generuje mniej ciepła, zapewnia optymalne natężenie światła i trwałość. DLA KONKRETNEGO POJAZDU. Ta nieoryginalna wiązka przewodów pojazdu z przyczepą jest przeznaczona dla wybranych roczników Mitsubishi Outlander. ŁĄCZNIK STANDARDOWY. Te 4-płaskie przewody przyczepy z wtyczką można wykorzystać do podłączenia tylnych świateł przyczepy, świateł hamowania i kierunkowskazów. Czterokierunkowe okablowanie świateł przyczepy jest popularne w różnych przyczepach, dodając wszechstronne opcje holowania pojazdu. ŁATWE DO ZAINSTALOWANIA. Żadnego cięcia! Bez łączenia! Ten zestaw wiązki przewodów przyczepy można podłączyć do istniejącego fabrycznego okablowania pojazdu i wyposaża go w standardowe tylne 4-stykowe złącze przewodów przyczepy do podłączania i holowania przyczepy.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.3 4.3 out of 5 stars 118 ratings 4.3 out of 5 stars
Exterior ‎Painted
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 6 x 3 inches
Item model number ‎56189
Item Weight ‎1.4 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎56189
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎56189
Product Dimensions ‎9 x 6 x 3 inches

3.4

13 Review
5 Star
69
4 Star
13
3 Star
7
2 Star
3
1 Star
7

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: ABC
Working just fine.
For whatever reason, the original wiring harness for my trailer lights failed. I ordered this one to fit my car and I now have trailer lights again. Since I didn't have a place to work on the car, I had our local U-Haul install the wiring harness.
Scritto da: DOBY DADDY
not plug and play
I thought this is supposed to be plug and play. The power wire is not plug and play and needs to be ran under the carpet along the edge so door sill panels and center column lower trim panel need to be taken off. I didn't go through the firewall. I just plugged it into the fuse box under the dash. Also had to drill a hole in the rear floor pan above the spare tire so the spare tire had to be dropped. Whole thing took about an hour.
Scritto da: Rev DoPray
2018 Mitsubishi Outlander Phev Successful Install
I was able to install this into my 2018 Mitsubishi Outlander PHEV GT S-AWC. Everything was hooked up in the back without needing to run the wire under the car to the battery. I just hooked it up to the battery in the back. There also wasn’t a need for any trim/panel removal tools. The instructions were useless but I simply looked at the wiring diagram and installed it. Although I haven’t tested it with my trailer I am giving this product 5-Stars. If I run into difficulty with it functioning correctly I will update my review.
Scritto da: Asher04
Not for Vehicle that already has Factory Tow Package
Before you buy this product - check to see if your vehicle has the factory tow package included. To find out if you do, check the installation video from etrailer (for their product) and the installer will point out in the hood what you need to look for. If you do have the factory tow package go with the model #56296 (ignore the vehicle fit from Amazon: it will say it will not fit your vehicle). Only go with this product if you don't have the factory tow package. I didn't realize I had the factory tow package until I went through the installation steps.
Scritto da: Jana M. Kleffman
Worked Great
Did what it said it was gonna do. Took about 30 minutes to install, nothing complex. Make sure you have the ability to lift your vehicle because you are going to need to crawl along the ground a bit to get the wire up to the front of the vehicle. Not a big issue with ramps. Overall, good kit.
Scritto da: Jason Brinckmann
Watch my video for Installation!!!!
The media could not be loaded. Everything you need and not too terrible to install yourself! Watch my detailed video for a complete overview on the installation because the instructions page that it comes with (-1 star) has incomplete written directions and the photos only show the panel removing in the trunk.
Scritto da: Moises Pimentel
To connect it’s on the driver side left side thank you
It fits perfectly on the video it shows on the right side of the rear end of the 2018 outlander but on the outlander it will be on the left rear of the light fixture the only thing that was different but it works perfectly fine thank you
Scritto da: TLB
Works great
Works great on my three row 2019 Mitsubishi Outlander. Easy to setup even though I had to crawl under my car to run the wire to the engine bay. Electrical tape helps keep the connectors attached to the wires.
Scritto da: Martin Thomas
Good quality and very nice custom fit
Easily plugs into lighting system for a professional installation.
Scritto da: John
No wires to splice
2015 outlander . Easy plug-ins. No cut wires , so if electrical problems come up later you can unplug harness and start trouble shoot the vehicle only . - Routing wire too frount of vehicle can be done with no drilling but a little of a challenge if you are not a young man ????
Scritto da: Amazon Customer
Easy install and working fine
I purchased and installed myself following instructions from YouTube. It's working great.
Scritto da: Gary wilkinson
Excellent and on time
Scritto da: Jim B.
Good for a 2019 Mitsubishi outlander phev
Used this on a 2019 Mitsubishi outlander phev worked great.

Produkty powiązane

hot

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array