CURT 31108 2-calowy przedni zaczep odbiornika, wybierz Chevrolet Silverado, Suburban, GMC Sierra, Yukon XL, przycinanie powięzi

Brand:CURT

3.5/5

1899.47

ŁATWA INSTALACJA. Ten przedni hak holowniczy pasuje do wybranych modeli Chevy Silverado 1500 HD, Classic, 2500 HD, Classic, 3500, Classic lub Suburban 2500 oraz GMC Sierra 1500 HD, Classic, 2500 HD, Classic, 3500 lub Yukon XL 2500. ODPORNY NA KOROZJĘ. Aby zapewnić doskonałą ochronę przed rdzą, odpryskami i uszkodzeniami spowodowanymi promieniowaniem UV, ten przedni podnośnik jest pokryty dwuwarstwową, odporną na rdzę powłoką A, która pokrywa zaczep od wewnątrz i na zewnątrz, oraz bardzo trwałą czarną powłoką proszkową. TESTOWANA KONSTRUKCJA. Ten przedni zaczep został w pełni przetestowany pod kątem bezpieczeństwa w naszym zakładzie inżynieryjnym w Detroit. Testujemy nasze konstrukcje przedniego zaczepu przyczepy zgodnie ze specyfikacjami SAE J684. NIEZAWODNA WYTRZYMAŁOŚĆ. Ten przedni zaczep jest oceniany na 5000 funtów. GTW i 500 funtów. waga języka. Jest również oceniany na 9000 funtów. zdolność uciągu w linii prostej do holowania awaryjnego i zastosowań z wyciągarką (ograniczona do elementu holowniczego o najniższej wartości znamionowej). WSZECHSTRONNY ODBIORNIK. Dodaj przydatny odbiornik zaczepu z przodu pojazdu za pomocą tego przedniego zaczepu odbiornika. Standardowy 2-calowy odbiornik umożliwia zamocowanie pługa śnieżnego, bagażnika, bagażnika rowerowego, haka holowniczego, mocowania wyciągarki lub innego osprzętu do holowania.

Brak dostępnych jednostek
ŁATWA INSTALACJA. Ten przedni hak holowniczy pasuje do wybranych modeli Chevy Silverado 1500 HD, Classic, 2500 HD, Classic, 3500, Classic lub Suburban 2500 oraz GMC Sierra 1500 HD, Classic, 2500 HD, Classic, 3500 lub Yukon XL 2500. ODPORNY NA KOROZJĘ. Aby zapewnić doskonałą ochronę przed rdzą, odpryskami i uszkodzeniami spowodowanymi promieniowaniem UV, ten przedni podnośnik jest pokryty dwuwarstwową, odporną na rdzę powłoką A, która pokrywa zaczep od wewnątrz i na zewnątrz, oraz bardzo trwałą czarną powłoką proszkową. TESTOWANA KONSTRUKCJA. Ten przedni zaczep został w pełni przetestowany pod kątem bezpieczeństwa w naszym zakładzie inżynieryjnym w Detroit. Testujemy nasze konstrukcje przedniego zaczepu przyczepy zgodnie ze specyfikacjami SAE J684. NIEZAWODNA WYTRZYMAŁOŚĆ. Ten przedni zaczep jest oceniany na 5000 funtów. GTW i 500 funtów. waga języka. Jest również oceniany na 9000 funtów. zdolność uciągu w linii prostej do holowania awaryjnego i zastosowań z wyciągarką (ograniczona do elementu holowniczego o najniższej wartości znamionowej). WSZECHSTRONNY ODBIORNIK. Dodaj przydatny odbiornik zaczepu z przodu pojazdu za pomocą tego przedniego zaczepu odbiornika. Standardowy 2-calowy odbiornik umożliwia zamocowanie pługa śnieżnego, bagażnika, bagażnika rowerowego, haka holowniczego, mocowania wyciągarki lub innego osprzętu do holowania.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.5 4.5 out of 5 stars 212 ratings 4.5 out of 5 stars
Exterior ‎Gloss Black Powder Coat
Finish Type Powder Coated
Is Discontinued By Manufacturer ‎No
Item model number ‎31108
Item Weight 29 Pounds
Item Weight ‎29 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎31108
Material Carbon Steel
Model ‎Front Mount Hitch
OEM Part Number ‎31108
Product Dimensions ‎42 x 20 x 10 inches
Vehicle Service Type Marine-Personal-Craft, Van, Sport-Utility-Vehicles, Truck, Trailer

3.5

12 Review
5 Star
73
4 Star
13
3 Star
8
2 Star
2
1 Star
3

Napisz recenzję

Twój e-mail nie zostanie opublikowany. Wszystkie pola obowiązkowe są oznaczone symbolem*

Scritto da: pdgrimes
SO EASY -No need to remove your factory tow hooks if you have them on Chevy/GMC 2500 HD Classic
I have a 2007 Chevy/GMC 2500 HD Classic. Ad says you need to remove your factory tow hooks but that was not true for mine. Each tow hook has three threaded holes and easily slides into the front of the frame -one for each side of the frame and one for the bottom frame hole. This hitch mounts to the two inner holes and the two underside holes. I left the outside tow hook bolts on, loosened them just so I could wiggle the hooks around to line up the holes again for the hitch and reinstalled them. Took just a few minutes with no help. You can use your existing hardware, theirs, or mix/match, heads are different sizes but threads are the same. I used nothing but a common metric socket set. I trimmed a little of the lower plastic bumper skirt with a jigsaw just so the hitch would push up on it slightly but it was not even necessary. Not sure if this is the case for all makes/models this hitch fits but certainly any like my body style. Only four mount bolts but they are beefy enough. Not worried about carrying my back rack or pushing trailers around. Plenty solid.
Scritto da: Robert Falen
Well made
Very easy to install . Only took about 10 minutes. Well made and recieved it on time.
Scritto da: Amazon Customer
Be prepared to cut or drill
Good product but unfortunately GM or Curtis don’t have the same specs. Was thinking about a hour to install but it took 2
Scritto da: Patrick Walker
No hardware or instructions included however...
it's quite simple: 6 grade 8 (GR8 bolts), nuts and 12 washers. 2 @ 1.75, 4 @ 12mm X 45mm or 4 @ 7/16 X 1.75. I'm not using the hitch to pull anything it's for a utility rack carrying less than 400lbs so I trust my hardware will work fine. Installation is about 15-20 minutes. My truck: 2006 Chevy 2500HD w/o tow hooks
Scritto da: richard bomgardner
Great Solution for Winch Mount!
Very Impressed with this product. I drive a 2001 2500HD 4 door longbox Silverado ado with the Duramax and install was a breeze. Like others said, getting the washers in the right spot between the frame and the receiver was the toughest part but it still only took me an hour by myself. If you're like me, you were skeptical of this unit destroying you ground clearance. I was thinking I would by this to save myself some fabrication time, and cut it apart and move the receiver up higher and into a hole in the bumper. well I installed it for giggles last night and I was very impressed with the design. Curt got the receiver as absolutely high off of the ground as possible without requiring bumper modification. In fact, I lost Zero ground clearance. The lowest part of the receiver still sits about a half inch higher than the first cross member that the lower a arms bolt to. My pickup is stock ride height and tires and I still have 12" of clearance underneath the reciever. The receiver doesn't stick out any further than the bumper either. It is actually about 3/4" rearward of the front face of the bumper. I did sacrifice some approach angle but this 21' long boat is not exactly a rockcrawler so I think I'll be just fine. I bought this to use as a winch mount and I think this is going to be perfect. I was impressed that it is rated at 9,000 pounds for a straight line pull with only 4 bolts holding it in.
Scritto da: B and B
Perfect
I just installed this on my 2002 Silverado 2500HD. I’m not sure why they say you must remove the factory tow hooks, instructions give you 2 options - installing with or without the factory tow hooks. I left mine on, it bolted right up. I did it myself in about 30 minutes. Original bolts are 18mm, new ones are M12 19mm I torqued to 78 foot pounds. Super fast, super easy, and it’s rock solid. I also didn’t have to trim any front plastic - it pushed it up a bit but who cares - you can’t see it. Going to use it for a bike rack. Great!!
Scritto da: Amazon Customer
Second time's the charm
This model worked, but Amazon's fit guide originally said it wouldn't and recommended a different model (31302) that I purchased for my 2005 Chevy Avalanche 2500. Before I even tried to install the first one I called Curt's tech support as their instructions cited a couple of different GMC/Chevy models, but not mine so I was suspicious from the start. Their tech support assured me the model recommended by Amazon's fit guide would work for my model. After about an hour of frustration I called back and spoke to the same tech assuring him there was no way it was going to fit and that the diagram they showed for my frame in their instructions didn't even match mine. (Granted, there aren't too many 3/4 ton Avalanches out there and when you add the variables of whether the model has the Tupperware (i.e. cladding) around it or not, it's not the easiest model to accommodate, but come on, we're talking the frame here.) To his credit, he asked me to email him some pictures and he'd discuss it w/ an engineer on Monday morning. (I was impressed to be able to speak w/ a customer service rep late on a Friday.) Before doing that I went to eTrailer.com and saw they recommended this model (31108) for my vehicle, not the 31302 and had Curt's install diagram available for download which confirmed it matched my frame. I would've preferred giving eTrailer.com my business for their value added service, but by this point it was easier to do the exchange through Amazon. While I'd only give Amazon's fit guide 1 star (and at least for the Avalanche, I see from other reviewers I'm not alone), their exchange service was superb in that the replacement arrived w/in a few days and they paid the return shipping (for one heavy chunk of metal) both ways and dispatched UPS to pick it up the wrong part from my front door.
Scritto da: Mario Gendron
Attache Avant GMC 2002 1500
Pour Ma Part la Piece est bien construie Mais il a fallue que je modifie un peut Peut etre avec des mesure en pouces pour adaptation chacque Rebord du frame serai bien pour les Utulisateure !
Scritto da: Northern R
Is as advertised.
Fit exactly as advertised and looks great. It even came 3 days early straight to my door. Hardware included for mounting.
Scritto da: KE
Fit perfectly, exactly as described.
Don’t normally write reviews, but this was delivered before the promised date and installed as described without any issues. Quick easy installation and of good quality, would recommend without any reservation.
Scritto da: Tony
Curt 31108 front mount hitch
Arrived complete and well packaged. Included instructions are a little vague. YouTube has great install videos. Installed on my 2007 Chevrolet Silverado 2500 HD, old body style, in about an hour. As others have mentioned, tightening the side bolts once the hitch is positioned is a little tricky with the air dam in place. I did not need to trim the air dam for the install. Happy with my purchase.
Scritto da: NeilM108
Works great. Fit perfectly
Delivery was fast. Instructions were a bit brief for the average DIY'r, but I did get it done. It fit perfectly. It would be very difficult to install without an air ratchet (not a lot of room for a hand socket).

Produkty powiązane

hot
Camco 48473 Eaz Lift RV Zaczep zderzaka
3.7/5

zł 528.24

Camco 48473 Eaz Lift RV Zaczep zderzaka
3.7/5

zł 528.24

Odkryj naszą międzynarodową sieć

Wysyłamy do 28 krajów, ponad 200 000 produktów. Bądź na bieżąco, zapisz się do newslettera.

Array